Planet-technology ISW-800M Manuale Utente

8-Port Managed Industrial Ethernet Switch ISW-800M User's Manual

Figure 2-1 ISW-800M Front Panel 2.1.3 LED Indications LED Status Meaning Green The switch unit is power on. Power Off The switch unit is no powe

Off No device attached Yellow The port is operating in full-duplex mode. Blinks Collision of Packets occurs in the port. FDX/COL (Port 7 & 8)

OFF Disable port 6 Alarm 6 ON Enable port 6 Alarm. If the port’s link fails, the fault LED will light up. OFF Disable port 7 Alarm 7 ON Enable port

V - V + V - V + 1. Insert the positive and negative wires into the V+ and V- connector on the terminal block co

Fault Alarm Contact24V DC Buzzer 24V BatteryThe open circuit will form when the power failure or port link failure.The fault alarm device will send a

Step2: Lightly push the button of DIN-Rail into the track. Step3: Check the DIN-Rail is tightly on the track. Step4: To remove the industrial switch

Step3: Use the screws to screw the wall mount plate on the industrial switch. Step4: Use the hook holes at the corners of the wall mount plate to h

3. NETWORK INSTALLATION 3.1 Hardware Installation In this paragraph, we will describe how to install the 8-Port 10/100TX with redundant ring Web manag

3.3 Redundant Ring Application The industrial switch supports the redundant ring protocol that can help your network system to recovery from network

3.4 Coulping Ring Application In the network, it may have more than one redundant ring group. By using the coupling ring function can connect each re

Trademarks Copyright ○c PLANET Technology Corp. 2006. Contents subject to which revision without prior notice. PLANET is a registered trademark o

3.5 Dual Homing Application Dual Homing function is to prevent the connection lose between redundant ring group and upper level/core switch. Assign tw

4. WEB MANAGEMENT This section introduces the configuration and functions of the Web-Based management. The following configuration steps are based on

The Web management interface 4.4 Port Status In Port status, you can view every port status that depended on user's setting and the negotiation

4.5 Single port information You can click the port on the Panel figure on the left side of web GUI. Then, the single port information window will po

to clean all counts. Port Statistics Interface 4.7 Port Control You can change the port status. 1. Select the port by scroll the Port column. 2. St

Port Control interface 4.8 Switch Settings You can assign the system name and location and view the system information. 。 System Name: assign the na

Switch Settings interface [NOTE] Remember to execute the "Save Configuration" action, otherwise the new configuration will lose when the sw

Port Mirroring intrerface 4.10 VLAN configuration A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you

VLAN Configuration interface 4.10.1 Port-based VLAN Packets can go among only members of the same VLAN group. Note all unselected ports are treated as

VLAN – Port-based Add interface 6. You will see the VLAN group displays. 7. If the groups' list is more than one page, you can click to view

Table of Contents 1. INTRODUCTION... 5

802.1Q VLAN interface 4.10.2.1 Basic 1. Click Add button. 2. Management VLAN ID: it is used for remote management security. Only the port of VLAN gr

802.1Q VLAN – Add interface 6. Click . Then you will see the page as follow.

7. To set the outgoing frames are VLAN-Tagged frames or untagged. Then click . 。 Tag: outgoing frames with VLAN-Tagged. 。 Untag: outgoing frames w

user. You can set up the mail server IP, mail account, and forwarded email account for receiving the event alert. 1. Email Alert: enable or disable t

alert to the dedicate SMTP server. ¾ Power status: when the device power status has changed, the system will send out the alert to the dedicate SMTP

Power Alarm interface 4.12 IP Configuration Power alarm function enables the Relay alarm action. Without enabling power alarm function, the Relay ala

IP Configuration interface 4.13 SNTP Configuration You can configure the SNTP (Simple Network Time Protocol) settings. The SNTP allows you to synchro

ALA - Alaskan Standard -9 hours 3 am HAW - Hawaiian Standard -10 hours 2 am Nome, Alaska -11 hours 1 am CET - Central European FWT - French Wint

SNTP Configuration 4.14 IP Security IP security function allows you to assign 10 specific IP addresses that have permission to access the switch thro

IP Security interface 4.15 RSTP Configuration The Rapid Spanning Tree Protocol (RSTP) is an evolution of the Spanning Tree Protocol and provides for

4.12 IP Configuration... 35 4.13 SNTP Configur

Rapid Spanning-Tree Protocol learning and listening states to the forwarding state. Enter a value between 4 through 30. [NOTE] 1. Must follow the ru

mathematic calculation. False is including the STP mathematic calculation. 7. Click button. [NOTE] Remember to execute the "Save Configuration&q

The system also supports the coupling ring that can connect 2 or more redundant ring group for the redundant backup function and dual homing function

[NOTE] 1. When you enable the redundant ring function, you must disable the RSTP. The redundant ring function and RSTP function cannot exist at the

QoS Configuration interface 4.18 IGMP The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP m

IGMP Snooping interface 4.19 SNMP Configuration The SNMP is a Protocol that governs the transfer of information between management and agent. The swi

4.19.3 Trap Manager A trap manager is a management station that receives traps, the system alerts generated by the switch. If no trap manager is defin

Security Manager interface. 4.21 Configuration Backup In Configuration Backup, you can restore the backup configuration into the industrial switch. A

TFTP Restore Configuration interrface 4.21.2 TFTP Backup Configuration You can save current flash ROM value from the industrial switch to the TFTP se

4.21.3 TFTP Update Firmware It provides the functions to allow a user to update the switch firmware. Before updating, make sure you have your TFTP ser

1. INTRODUCTION The 8-Port 10/100TX with redundant ring Web management industrial switch is a cost- effective solution and meets the high reliability

Factory Default interface 4.23 Save Configuration Save the industrial switch configuration to the flash memory. Power off the industrial switch witho

4.24 System Reboot Reboot the Switch in software reset. Click button to reboot the switch. System Reboot interface 4.25 Rate Control You can set u

2. Qos and Rate control cannot be existed at the same. Rate Control interface 4.26 System Log You can set up system log events and view the system l

System Log Configuration 4.26.2 Event Configuration You can select the system log events. When selected events occur, the system will send out the lo

Event Configuration interface

5. TROUBLESHOOTING This section is intended to help you solve the most common problems on the industrial Ethernet switch. 5.1 Incorrect connections Th

IF the power indicator does turn on when the power cord is plugged in, you may have a problem with power outlet, or power cord. However, if the Switch

6. APPENDIX 6.1 100BASE-TX/10BASE-T Pin Assignments With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for

▫ CSMA/CD Protocol ▫ RJ-45 Port support auto MDI/MDI-X function ▫ 2K MAC address table ▫ 1Mbit memory buffer ▫ 2.0Gbps back-plane ▫ Wide-range re

MAC address 2K Memory Buffer 1Mbit Network Cable 10Base-T : 2-pair UTP/STP Cat 3, 4, 5 cable 100Base-TX: 2-pair UTP/STP Cat. 5 cable 10Base-T: EIA/

128kbps, 256Kbps, 512Kbps, 1MB, 2MB, 4MB, and 8MB. Ingress filter packet type combination rules are Broadcast/Multicast/Unknown Unicast packet, Broadc

2. HARDWARE INSTALLATION This section describes the functionalities of the Switch's components and guides how to install it on the rack or mount